A curved cabinet piece under construction in our Fort Lauderdale mill, with a table saw in the background
Home / Blog / Four Seasons Surfside: custom doors, cabana dry bars and restaurant serving stations
Commercial

Four Seasons Surfside: custom doors, cabana dry bars and restaurant serving stations

What Delta Woodworks built for the Four Seasons Hotel at The Surf Club in Surfside: hand-stained custom doors, cabana dry bars and painted serving stations.

Hotel millwork is judged up close. Guests touch the doors, lean on the bars and see the serving stations every time they sit down to eat. We were glad to work on the Four Seasons Hotel at The Surf Club in Surfside. This post covers what we built there, and what a hotel team can take from it when planning custom millwork of their own.

What we built at the Four Seasons in Surfside

Our scope covered three kinds of custom work:

  • Hand-stained custom doors with inset fabric panels. The doors were stained by hand, and each carries inset fabric panels framed in metallic trim.
  • Dry bars for the cabanas. Private dry bars built for the hotel's cabanas.
  • Rounded serving stations for the restaurant. Sculpted, rounded serving stations with a painted finish, built for the hotel's restaurant.

All of it was designed, fabricated and built in the USA in our Fort Lauderdale shop.

A curved cabinet piece under construction in our Fort Lauderdale mill, with a table saw in the background
A curved cabinet piece under construction in our Fort Lauderdale mill. This is a shop photo, not a photo of the Four Seasons job.

Custom doors: stain, fabric and metal in one piece

A door with an inset fabric panel and metallic trim brings three materials together in a single assembly. The stained wood frame, the fabric and the trim each behave differently, and they have to meet cleanly at the joints. On a hotel job, that means settling a few things before anything is cut:

  • The stain sample. Wood takes stain differently from one board to the next. An approved sample, reviewed by the design team in the same light as the finished room, gives everyone the same target.
  • The fabric. The fabric is normally chosen by the designer. We need the actual material and its thickness early, because the panel opening and the trim are sized around it.
  • The metallic trim. The profile, finish and how it is fixed to the frame all go on the shop drawings so the design team can approve them.

Our own mill makes it practical to stain, assemble and check the pieces under one roof, and to adjust a sample if the design team asks for a change. See our guide to paint, stain and lacquer finishes.

Cabana dry bars

A dry bar is a bar without plumbing: a counter, storage and a place to set out glassware and drinks. A cabana version has to fit a small, defined space and look at home in it. When we plan a dry bar, we start with what it has to hold (glassware, bottles, an ice bucket, a small appliance) and work the layout around that list. The drawings then show the doors, drawers and open shelves in their final positions, so the design team can approve them before the shop starts cutting.

Rounded serving stations in a painted finish

Serving stations carry a restaurant's service. They need drawers and shelves for flatware, linens and supplies, and a surface staff can use all shift. Curved fronts add a design feature, and they add shop work too: curved panels are cut and shaped to the drawn radius, then finished so the paint reads as one smooth surface. Painted finishes show everything beneath them, so the prep before the paint goes on matters as much as the paint. Read more in our guide to restaurant storage cabinets.

What hotel teams can take from this

  • Send the drawings early. Doors, bars and stations are all custom, and the shop drawings are where the details get settled.
  • Approve samples before production. Stain, paint and trim samples approved up front prevent rework.
  • Plan the lead time. Our lead time is 8-12 weeks after drawings are approved.
  • Expect one shop to handle the whole run. Our own crew installs what we build, and we work with the general contractor and the other trades on site.

We build our custom work with Columbia Forest PureBond plywood and Blum hardware, and where a project specifies other materials, we build to the approved spec.

Planning hotel millwork with Delta

For more on how we approach hotel work, see our guides to hotel millwork and casegoods and hotel lobby millwork, and our restaurant and hotel millwork page. Our other hotel job is covered in AC Hotel by Marriott Fort Lauderdale. We serve Broward, Miami-Dade and Palm Beach counties; see our service areas. We're rated 4.8 on Google from 87 reviews.

Call 954-939-8579 or visit our Fort Lauderdale showroom at 2416 S Andrews Ave, Fort Lauderdale, FL 33316, Monday to Friday 9 to 5. The showroom has prefab and RTA door samples, and it is a good place to talk through a commercial project.

FAQ

Frequently asked questions

What did Delta Woodworks build for the Four Seasons in Surfside?

Hand-stained custom doors with inset fabric panels framed in metallic trim, dry bars for the hotel's cabanas, and rounded, painted serving stations for the hotel's restaurant.

Where was the work built?

Our custom work is designed, fabricated and built in the USA in our Fort Lauderdale shop, and our own crew installs it.

How long does a custom hotel millwork order take?

Our lead time is 8-12 weeks after drawings are approved.

Can you build doors with fabric panels and metal trim for other projects?

Yes, we build custom doors to the drawings and finishes your design team approves. Send the drawings or call the shop to talk through the scope.

Have drawings for a hotel or restaurant job?

Send the plans or a floor plan, or call the shop to talk through scope and timing.